Logo

Documentation

AntreaProxy

Table of Contents

Introduction

AntreaProxy was first introduced in Antrea v0.8 and has been enabled by default on all platforms since v0.11. AntreaProxy enables some or all of the cluster’s Service traffic to be load-balanced as part of the OVS pipeline, instead of depending on kube-proxy. We typically observe latency improvements for Service traffic when AntreaProxy is used.

While AntreaProxy can be disabled on Linux Nodes by setting the AntreaProxy Feature Gate to false, it should remain enabled on all Windows Nodes, as it is needed for correct NetworkPolicy implementation for Pod-to-Service traffic.

By default, AntreaProxy will only handle Service traffic originating from Pods in the cluster, with no support for NodePort. However, starting with Antrea v1.4, a new operating mode was introduced in which AntreaProxy can handle all Service traffic, including NodePort. See the following section for more information.

AntreaProxy with proxyAll

The proxyAll configuration parameter can be enabled in the Antrea configuration if you want AntreaProxy to handle all Service traffic, with the possibility to remove kube-proxy altogether and have one less DaemonSet running in the cluster. This is particularly interesting on Windows Nodes, since until the introduction of proxyAll, Antrea relied on userspace kube-proxy, which is no longer actively maintained by the K8s community and is slower than other kube-proxy backends.

Note that on Linux, even when proxyAll is enabled, kube-proxy will usually take priority and will keep handling NodePort Service traffic (unless the source is a Pod, which is pretty unusual as Pods typically access Services by ClusterIP). This is because kube-proxy rules typically come before the rules installed by AntreaProxy to redirect traffic to OVS. When kube-proxy is not deployed or is removed from the cluster, AntreaProxy will then handle all Service traffic.

Removing kube-proxy

In this section, we will provide steps to run a K8s cluster without kube-proxy, with Antrea being responsible for all Service traffic.

You can create a K8s cluster without kube-proxy with kubeadm as follows:

kubeadm init --skip-phases=addon/kube-proxy

To remove kube-proxy from an existing cluster, you can use the following steps:

# Delete the kube-proxy DaemonSet
kubectl -n kube-system delete ds/kube-proxy
# Delete the kube-proxy ConfigMap to prevent kube-proxy from being re-deployed
# by kubeadm during "upgrade apply". This workaround will not take effect for
# kubeadm versions older than v1.19 as the following patch is required:
# https://github.com/kubernetes/kubernetes/pull/89593
kubectl -n kube-system delete cm/kube-proxy
# Delete existing kube-proxy rules; there are several options for doing that
# Option 1 (if using kube-proxy in iptables mode), run the following on each Node:
iptables-save | grep -v KUBE | iptables-restore
# Option 2 (any mode), restart all Nodes
# Option 3 (any mode), run the following on each Node:
kube-proxy --cleanup
# You can create a DaemonSet to easily run the above command on all Nodes, using
# the kube-proxy container image

You will then need to deploy Antrea, after making the necessary changes to the antrea-config ConfigMap:

kind: ConfigMap
apiVersion: v1
metadata:
  name: antrea-config
  namespace: kube-system
data:
  antrea-agent.conf: |
    kubeAPIServerOverride: "<kube-apiserver URL>"
    antreaProxy:
      proxyAll: true    

The kubeAPIServerOverride option will enable the Antrea Agent to connect to the K8s apiserver. This is required now that kube-proxy is no longer running and that the Antrea Agent can no longer use the ClusterIP for the kubernetes Service during initialization. If you are unsure about which values to use, take a look at your Kubeconfig file, and look for a line like this one:

apiVersion: v1
clusters:
- cluster:
    server: https://192.168.77.100:6443

Then use this value as is (e.g., "https://192.168.77.100:6443") for kubeAPIServerOverride.

And that’s it! All you have to do now is make sure that the antrea-agent Pods came up correctly and perhaps validate that NodePort Services can be accessed correctly.

Windows Nodes

Assuming you are following the steps we documented to add Windows Nodes to your K8s cluster with Antrea, you will simply need to skip running kube-proxy:

Configuring load balancer mode for external traffic

Starting with Antrea v1.13, the defaultLoadBalancerMode configuration parameter and the service.antrea.io/load-balancer-mode Service annotation can be used to specify how you want AntreaProxy to handle external traffic destined to LoadBalancerIPs and ExternalIPs of Services. Specifically, the mode determines how external traffic is processed when it’s load balanced across Nodes. Currently, it has two options: nat (default) and dsr.

  • In NAT mode, external traffic is SNAT’d when it’s load balanced across Nodes to ensure symmetric paths. It’s the default and the most general mode.

  • In DSR mode, external traffic is never SNAT’d and backend Pods running on Nodes that are not the ingress Node can reply to clients directly, bypassing the ingress Node. Therefore, DSR mode can preserve the client IP of requests, and usually has lower latency and higher throughput. Currently, it is only applicable to Linux Nodes, encap mode, and IPv4 clusters. The feature gate LoadBalancerModeDSR must be enabled to use this mode for any Service.

You can make the following changes to the antrea-config ConfigMap to specify the default load balancer mode for all Services:

kind: ConfigMap
apiVersion: v1
metadata:
  name: antrea-config
  namespace: kube-system
data:
  antrea-agent.conf: |
    kubeAPIServerOverride: "<kube-apiserver URL>"
    antreaProxy:
      proxyAll: true
      defaultLoadBalancerMode: <nat|dsr>    

To configure a different load balancer mode for a particular Service, you can annotate the Service in the following way:

kubectl annotate service my-service service.antrea.io/load-balancer-mode=<nat|dsr>

Note: Configuring the load balancer mode is only meaningful when proxyAll is enabled and kube-proxy is not deployed, otherwise external traffic would be processed by kube-proxy rules before it reaches Antrea’s datapath. If kube-proxy was ever deployed in the cluster, its rules must be deleted to avoid interference. In particular, the following filter rule that drops packets in INVALID conntrack state could prevent DSR mode from working:

*filter
-A KUBE-FORWARD -m conntrack --ctstate INVALID -j DROP

Special use cases

When you are using NodeLocal DNSCache

NodeLocal DNSCache improves performance of DNS queries in a K8s cluster by running a DNS cache on each Node. DNS queries are intercepted by a local instance of CoreDNS, which forwards the requests to CoreDNS (cluster local queries) or the upstream DNS server in case of a cache miss.

The way it works (normally) is by assigning the the kube-dns ClusterIP to a local “dummy” interface, and installing iptables rules to disable connection tracking for the queries and bypass kube-proxy. The local CoreDNS instance is configured to bind to that address and can therefore intercept queries. In case of a cache miss, queries can be sent to the cluster CoreDNS Pods thanks to a “shadow” Service which will expose CoreDNS Pods via a new ClusterIP.

When AntreaProxy is enabled (default), Pod DNS queries to the kube-dns ClusterIP will be load-balanced directly by AntreaProxy to a CoreDNS Pod endpoint. This means that NodeLocal DNSCache is completely bypassed, which is probably not acceptable for users who want to leverage this feature to improve DNS performance in their clusters. While these users can update the Pod configuration to use the local IP assigned by NodeLocal DNSCache to the “dummy” interface, this is not always ideal in the context of CaaS, as it can require everyone running Pods in the cluster to be aware of the situation.

This is the reason why we initially introduced the skipServices configuration option for AntreaProxy in Antrea v1.4. By adding the kube-dns Service (which exposes CoreDNS) to the list, you can ensure that AntreaProxy will “ignore” Pod DNS queries, and that they will be forwarded to NodeLocal DNSCache. You can edit the antrea-config ConfigMap as follows:

kind: ConfigMap
apiVersion: v1
metadata:
  name: antrea-config
  namespace: kube-system
data:
  antrea-agent.conf: |
    antreaProxy:
      skipServices: ["kube-system/kube-dns"]    

When you want your external LoadBalancer to handle Pod traffic

In some cases, the external LoadBalancer for a cluster provides additional capabilities (e.g., TLS termination) and it is desirable for Pods to access in-cluster Services through the external LoadBalancer. By default, this is not the case as both kube-proxy and AntreaProxy will install rules to load-balance this traffic directly at the source Node (even when the destination IP is set to the external loadBalancerIP). To circumvent this behavior, we introduced the proxyLoadBalancerIPs configuration option for AntreaProxy in Antrea v1.5. This option defaults to true, but when setting it to false, AntreaProxy will no longer load-balance traffic destined to external loadBalancerIPs, hence ensuring that this traffic can go to the external LoadBalancer. You can set it to false by editing the antrea-config ConfigMap as follows:

kind: ConfigMap
apiVersion: v1
metadata:
  name: antrea-config
  namespace: kube-system
data:
  antrea-agent.conf: |
    antreaProxy:
      proxyLoadBalancerIPs: false    

With the above configuration, AntreaProxy will ignore all external loadBalancerIPs. Starting with K8s v1.29, feature LoadBalancerIPMode was introduced, providing users with a more fine-grained mechanism to control how every external loadBalancerIP behaves in a LoadBalancer Service.

  • If the value of LoadBalancerIPMode is LoadBalancerIPModeVIP or nil, the traffic destined for the corresponding external loadBalancerIP should follow the default behavior and get load-balanced at the source Node.
  • If the value of LoadBalancerIPMode is LoadBalancerIPModeProxy, the traffic destined for the corresponding external loadBalancerIP should be sent to the external LoadBalancer.

Starting with Antrea v2.0, AntreaProxy will respect LoadBalancerIPMode in LoadBalancer Services when the configuration option proxyLoadBalancerIPs is set to true (default). In this case, AntreaProxy will serve only the external loadBalancerIPs configured with LoadBalancerIPModeVIP, and those configured with LoadBalancerIPModeProxy will bypass AntreaProxy. If the configuration option proxyLoadBalancerIPs is set to false, AntreaProxy will ignore the external loadBalancerIPs even if configured with LoadBalancerIPModeVIP.

There are two important prerequisites for this feature:

  • You must enable proxyAll and remove kube-proxy from the cluster, otherwise kube-proxy will still load-balance the traffic and you will not achieve the desired behavior.
  • Your external LoadBalancer must SNAT the traffic, in order for the reply traffic to go back through the external LoadBalancer.

Known issues or limitations

  • Due to some restrictions on the implementation of Services in Antrea, the maximum number of Endpoints that Antrea can support at the moment is 800. If the number of Endpoints for a given Service exceeds 800, extra Endpoints will be dropped (with non-local Endpoints being dropped in priority by each Antrea Agent). This will be fixed eventually.
  • Due to some restrictions on the implementation of Services in Antrea, the maximum timeout value supported for ClientIP-based Service SessionAffinity is 65535 seconds (the K8s Service specs allow values up to 86400 seconds). Values greater than 65535 seconds will be truncated and the Antrea Agent will log a warning. We do not intend to address this limitation.
  • Due to the use of the “learn” action in the implementation of DSR mode, the cost of processing the first packet of each connection is higher than NAT mode. Therefore, establishing connections may be slightly slower, and you may observe lower transaction rate if short-lived connections dominate your traffic. This may be improved in the future.

Getting Started

To help you get started, see the documentation.